News
FAST STROKING HYDRAULIC PRESS FOR VELUX WINDOWS
Hydraulico is at the moment producing the 3rd press for the manufacture of critical fittings for windows, with high accuracy of forming geometry to the product.
The press is performing 32 strokes per minute at 330 ton with progressive dies giving severe off-centre load.
The characteristics of the press are the ability to cope with the off-centre loading and the fast pressing cycle. Having produced with 2 Hydraulico presses of same design the customer requested a new press with absolutely same capability but with a capacity of 330 ton instead of 250 ton as the two previously supplied Hydraulico presses.
Enhancing your productivity
Read more
HYDRAULICO PRESS UPGRADE IN DENMARK
Hydraulico Upgrade of an old 1500 ton Müller Press
Before Old manual control system
New Siemens control system New hydraulic tank at top left
New hydraulic tank side view Close-up of new hydraulic tank
This press is back in production of wheel rims after another successful Hydraulico upgrade..
Hydraulico’s scope of supply was to upgrade the press with new Siemens PLC control, make it comply with legislation, add an additional hydraulic tank, mount SICK light curtain on both front and rear, as well as replace pumps by new ones and new pipework. The hydraulic power pack was relocated from pit to press. An installation performed by skilled and experienced Hydraulico technicians within 2 weeks only.
Get your press up to date
A PRESS AS GOOD AS NEW
Hydraulico Upgrade of an old HydroForm 150 ton Press (manufactured in 1980)
The customer wanted, hydraulically and electrically, to modernize an old HF150 ton press. Hydraulico service technicians installed a new hydraulic tank, with new pumps and motors, mounted a new safety manifold, and equipped the press with an Allen Bradley SLC500 PLC control. Duration of work: 2 weeks only.
Get your press up to date
resale to danish customer
Specifications: SAP 500 – 3100x650
Bending of absolutely straight steel profiles for electrical cabinets.
Working with different press brakes could not give perfectly straight profiles.
Hydraulico designed a hydraulic pres to match the high demands, and checked the result using our experience of 20 years with finite element calculations before starting the production of the press. The result more than satisfied demand and one more press was ordered.
When a Danish manufacturer of advanced electrical panels and cabinets gave their specifications for a new press for bending steel profiles, there was one little detail that posed some speculation to the staff at Hydraulico.
The floor-to-ceiling height at the spot where the new press was to fit in was a mere 4.5 meters (15 feet). Given the other specifications for the press with 3 meter wide press table, the task didn’t seem easy to accomplish.
Rethinking press frame design
A press with a force of up to 500 tons and large press table normally requires a substantial height in order to ensure the necessary forming stability and frame rigidity.
Hydraulico’s solution to the problem was an entirely new press in mono block design. By mounting the slide on the outside of the frame it was possible to design a press small enough to fit into the narrow space, while still meeting customer specifications and expectations.
Upsetting, Triple-acting hydraulico press
Specifications: TAP400/200/200 – 1200x800
A long-time Hydraulico customer has received a 3rd Hydraulico press.
The press is specially designed to perform hot upsetting work in steel alloys and titanium, producing parts for Rolls Royce jet engines. Specially designed with servo-controlled upsetting for high accuracy forging.
A custom-built press according to customer specifications with a 400 ton clamping and 2 pcs 200 ton upsetting cylinders. Press table measuring 1200x800 mm.
fully automated PRESS LINE
Automated production line:
Deep drawn stainless steel sinks
The three Hydraulico presses will function in a fully automated production line and are equipped with the newest Hydraulico technologies for deep drawing, including the world-renowned Electronic Shimming™ technology that ensures extremely precise control of the blank hold during the drawing process.
Additionally, the customer decided to extend the order with a robot in order to make the automation process complete.
